How To Install A Backup Camera In A 2008 Ford F150

How To Install A Fill-in Camera On A Ford F150

F-150 backup mirror kit CS-FTR-F35. This kit will only work with trucks with an existing 16-pivot mirror connector. If you do not accept a connector, it is all-time to use kit CS-FTRa-332

Preparing The Surface area

Step 1

Remove the rear view mirror drinking glass prior to starting the project. We recommend working with a professional. The glass breaks very easily and virtually automobile glass companies tin do this for free.

Footstep 2

Apply angling line to remove the Ford emblem from the tailgate.

Step 3

Locate the center hole with your finger. Apply a razor knife to cut away record from eye hole as a square.

Pace 4

Locate the foursquare holes to the left and correct of the center hole. They are currently behind the tape. These are not the holes that the decal fits into. Cut the tape away from these holes in a square shape.

Step 5

Use the kit's two included trunk nut clips and push them into the left and right side square openings.

Installing The Wiring

Stride 6

Fish the kit'due south included camera cablevision through the tailgate and out the opening in the lesser of the Ford F150.

Stride vii

Pull the cord all the way through and connect the emblem to the body nut clips.

Step 8

Fasten the emblem to the tailgate using the kit's included body bolts.

Step 9

Open the tailgate up and lay flat. Fish the wire through the opening in the back of the bed. The opening is located between the bed of the truck and the tailgate.

Connecting The Camera

Step 10

Advisedly connect the camera to the chassis harness. It is keyed and but goes together i style. Push it in as tight as you can to ensure a good connexion.

Stride 11

Cutting off the alternate power supply certain and tuck it inside the harness. From hither we are going to make all of the connections in the cab.

Important Note: Call back that the red wire at the rear of the harness is only to be used if y'all do not want to locate a power source inside the cab. Both cherry-red wires are live when ability is applied.

Step 12

Road the chassis harness along the frame and come upwards into the engine compartment next to the brake booster.

Step 13

Button the harness through the main wiring grommet past putting a slit in the nipple at the pinnacle of the grommet.

Stride 14

Peel back the loom and feed the wire through the grommet. Exist conscientious not to harm the RCA end.

Footstep fifteen

Cut the excess loom to fit. The harness should pull nicely through the indented hole in grommet.

Pace xvi

Remove the overhead trim panel with a difficult tug or tool and disconnect the wires.

Step 17

Remove the terminal lock from the connector and pull off the face of the connector.

Installing The Camera Wiring

Footstep 18

Insert yellow and blackness video wires into connector: xanthous to pin eight and black to pin sixteen. Supercede the terminal lock.

Important Note: If there is no wire in pivot 2, you lot will also need to add together the CAN bus terminal as shown in instructions in kit.

Stride xix

Carefully cut away and remove the wire sheathing and then that the video wires can be paired with the master harness. The video wires volition exist covered using the black trim encompass included in the backup camera kit.

Step 20

Remove the a-colonnade cover with a tug. If you have a handle, remove the two bolts before tugging.

Stride 21

Remove the dash-side panel and road the RCA and camera power/ground wires from the kit up forth the a-pillar rail.

Step 22

Connect the RCA to the mirror RCA input. This can be tucked forth the headliner and the glass in the a-pillar.

Step 23

Route the power and ground wires to the upper center panel surface area.

Step 24

Locate the reverse-activated power wire in the mirror pine: blueish/white wire in pivot nine.

Pace 25

Utilise the kit'south tap splice to connect the photographic camera red wire to the reverse-activated power wire in the harness.

Step 26

Connect the camera back to the black wire in grounded pivot iv of the factory connect. Splicing, soldering, and shrink wrapping your connections is recommended.

The Final Touches

Step 27

Constrict the camera power/ground wires betwixt the headline and glass.

Step 28

Secure the wires against the a-pillar using potent tape. Make sure the airbag is clear. Reinstall the a-colonnade encompass.

Stride 29

Plug in the mirror and install on the wedge. If you want to test first (always a good idea), push it on only far plenty so it is on temporarily.

Pace 30

Test the camera by starting the truck and placing it in reverse. You should see the mirror light upwardly with a video epitome.

Step 31

Push wires back in overhead and put trim panel back in the headliner. Putting the headliner in place may take a few tries and a few skilful pushes.

Step 31

Snap the tailgate emblem on the housing.

Enjoy Your New F150 Fill-in Camera

Congratulations! You lot've simply installed a brand new backup photographic camera on your Ford F150. Now yous can enjoy the added convenience and safety a backup camera provides when parking or reversing.

If you lot need farther explanation of installation instructions, view your backup photographic camera kit'south instruction manual, or cheque out the video beneath:

Source: https://camerasource.com/blog/how-to-install-a-backup-camera-on-a-ford-f150/

Posted by: cresswellthaton1982.blogspot.com

Share this post